Search:

Type: Posts; User: Steve_M

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    28

    The Genuine Honda flexible hoses are discontinued...

    The Genuine Honda flexible hoses are discontinued in Europe.

    They are Beat specific parts 46430-SS1-003 Rear & 46410-SS1-003 Front.

    Your only chance would be either Japan or some used ones if...
  2. Thread: Wipers

    by Steve_M
    Replies
    2
    Views
    61

    Its same as used on a 1984-1987 Civic or CRX...

    Its same as used on a 1984-1987 Civic or CRX passenger side blade - part number 38480-SB2-602
  3. Replies
    5
    Views
    434

    DTC 8 is TDC sensor (In distributor) DTC 9 is...

    DTC 8 is TDC sensor (In distributor)

    DTC 9 is CYL Sensor (Behind camshaft sprocket)

    http://www.u-ukhbc.co.uk/troubleshooting.htm

    "This car has been in dry storage for 4 years and was ok when...
  4. Replies
    5
    Views
    434

    https://drive.google.com/open?id=1u_7MCC2TTtua6lcw...

    https://drive.google.com/open?id=1u_7MCC2TTtua6lcwmmJZfD_FL0J-CaiD
  5. Replies
    5
    Views
    434

    There is no voltage spec in shop manual for the...

    There is no voltage spec in shop manual for the TDC sensor, you need to be working from the resistance of the sensor and continuity of the harness back to the ECU.

    Check resistance at sensor 4 pin...
  6. Crank bearing 1. C2 = Green (D) =...

    Crank bearing

    1. C2 = Green (D) = 13324-P36-003 x 2
    2. C3 = Brown (C) = 13323-P36-003 x 2
    3. C2 = Green (D) = 13324-P36-003 x 2
    4. C2 = Green (D) = 13324-P36-003 x 2

    Big end
    1. B2 = Yellow...
  7. Thread: Number Plates

    by Steve_M
    Replies
    4
    Views
    326

    Not technically legal, but I had a custom sized...

    Not technically legal, but I had a custom sized plate to the same scale as a normal UK plate.

    2774
  8. Replies
    3
    Views
    275

    If your meaning the CYL sensor, its buried behind...

    If your meaning the CYL sensor, its buried behind the camshaft sprocket, which will be a cambelt cover, belt and sprocket off to access it.

    Best to change the belt while your there if you don't...
  9. Replies
    3
    Views
    325

    There is no part number for the TDC sensor, as...

    There is no part number for the TDC sensor, as its not available separately, only as a complete distributor.
  10. Thread: Engine Manual

    by Steve_M
    Replies
    5
    Views
    856

    PM sent to you

    PM sent to you
  11. Connector pin locations for Crank Angle Sensor

    Connector pin locations for Crank Angle Sensor
  12. The crank angle sensor is in the distributor. ...

    The crank angle sensor is in the distributor.

    I would have initial said about checking that the timing is spot on, but if the distributor has been changed that would surely had an effect on it....
  13. Replies
    27
    Views
    4,195

    Yes, 2 different suppliers originally, I expect...

    Yes, 2 different suppliers originally, I expect one has superseded to the other by now, so only one type would be available.

    http://www.taihonet.co.jp/e/engine_b.html
    ...
  14. Replies
    27
    Views
    4,195

    You should have the numbers 1,2,3,4 on the rods...

    You should have the numbers 1,2,3,4 on the rods across the rod/cap joint, you need to read the letters from the crank (A, B, C, D) then look up the correct shell on the matrix
    ...
  15. Thread: Engine Manual

    by Steve_M
    Replies
    5
    Views
    856

    PM sent Regards

    PM sent

    Regards
  16. Replies
    27
    Views
    4,195

    It's in Japanese, but the Engine Shop Manual...

    It's in Japanese, but the Engine Shop Manual download below may help you.

    https://drive.google.com/open?id=1wLrmjFtk1jDB6bun7PRAUcxlKaF9PVvP
  17. Its normally best to use a crankshaft pulley...

    Its normally best to use a crankshaft pulley counterhold tool when undoing the pulley bolt. Its a 50mm internal hex in the pulley.
    ...
  18. Replies
    17
    Views
    3,199

    The clutch slave cylinder is hiding on top of the...

    The clutch slave cylinder is hiding on top of the gearbox under the shift cable bracket, you would need to disconnect the cables and remove that bracket (2 bolts) to gain access to the slave...
  19. Replies
    17
    Views
    3,199

    Are you now and why would you want to do that?

    Are you now and why would you want to do that?
  20. Thread: Vesion Z pics

    by Steve_M
    Replies
    5
    Views
    2,508

    Everglade Green Metallic G80M

    Everglade Green Metallic G80M
  21. Thread: Best ECU

    by Steve_M
    Replies
    7
    Views
    1,768

    New ECU are still available from a Honda Dealer...

    New ECU are still available from a Honda Dealer price is now 810 inc VAT - would come from Japan so could take a while to arrive.
  22. I would suspect the fuel pump main relay (Located...

    I would suspect the fuel pump main relay (Located behind the document box behind the passenger seat)

    When the vehicle wont start can the fuel pump be heard to prime when the ignition is turned on....
  23. Replies
    60
    Views
    13,113

    I just tried the google translate app via a photo...

    I just tried the google translate app via a photo of the shop manual and it works pretty well.

    First paragraph of page 5-10

    Engine adjustment - Check compression pressure * Check after warming...
  24. Replies
    60
    Views
    13,113

    That's from the Engine manual (60P3600) not the...

    That's from the Engine manual (60P3600) not the shop manual (60SS100)

    I have never seen any other language manual apart from Japanese, basically because the Beat was a Japan only model.

    There...
  25. Replies
    4
    Views
    1,164

    As fxdlidon says the original fixing are tenax...

    As fxdlidon says the original fixing are tenax fittings, if you want to get some they are available from the supplier Namrick
    ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4